Docomo F-01E Instruction Manual download pdf (Page 136)

ATS4=<n> Set the line feed (LF) character. When result code is displayed as alphabetic characters,

appends the character after the carriage return (CR) character.

n=10 (fixed value)

ATS4? : Display current settings

ATS4=10

ATS5=<n> Set the back space (BS) character. When this character is detected during command input,

the last character in the input buffer is deleted.

n=8 (fixed value)

ATS5? : Display current settings

ATS5=8

ATS6=<n> Set pause time (seconds) until dialing commences but do not operate.

n=2-10 (default : n=5)

ATS6? : Display current settings

ATS6=5

ATS8=<n> Set pause time (seconds) until commas are dialed but do not operate.

n=0-255 (default : n=3)

ATS8? : Display current settings

ATS8=3

ATS10=<n>

Set the delay time (1/10 seconds) for automatic disconnection but do not operate.

n=1-255 (default : n=1)

ATS10? : Display current settings

ATS10=1

ATS30=<n> Set a period of time (minutes) with no data transmission/reception to terminate the

connection for 64K data communications.

n=0-255 : (default : n=0, n=0 indicates that inactive timer is set to OFF.)

ATS30? : Display current settings

ATS30=0

ATS103=<n> Set the separator of received sub addresses for 64K data communication.

n=0 : ＊ n=1 : / (default) n=2 : ￥ or \

ATS103? : Display current settings

ATS103=1

ATS104=<n> Set the separator of sent sub addresses for 64K data communication.

n=0 : # n=1 : % (default) n=2 : &

ATS104? : Display current settings

ATS104=1

ATV<n>

Set result code display method.

n=0 : Number display n=1 : Alphabetical display (default)

When ATV0 is executed, "0" is not returned to the same line.

ATV1

ATX<n>

Set whether to detect busy or dial tones and whether to display the speed in the

"CONNECT" display for the connection.

Busy tone detection : Send "BUSY" response when dialup connection is busy.

Dial tone detection : Detect whether FOMA terminal is connected.

n=0 : No busy tone, no dial tone detected, and no speed is displayed

n=1 : No busy tone, no dial tone detected, and speed is displayed

n=2 : No busy tone, dial tone detected, and speed is displayed

n=3 : Busy tone detected, no dial tone detected, and speed is displayed

n=4 : Busy tone detected, dial tone detected, and speed is displayed (default)

When n=0 is set, AT&E and AT￥V command will be unavailable.

ATX4

ATZ

Reset the current setting to the registered state.

When this command is executed during communication, the terminal is reset after the line

is disconnected (displaying "NO CARRIER").

ATZ

OK (When in offline mode)

AT%V Display FOMA terminal version.

AT%V

Ver1.00

AT&C<n>

Set the operating conditions of the circuit CD (DCD) for DTE.

n=0 : Always ON n=1 : Vary according to line connection status (default)

When set to n=0, the CD signal is set to ON directly before sending "CONNECT" when

ending connection. The CD signal is set to OFF directly before the line is disconnected and

"NO CARRIER" is sent.

AT&C1

AT&D<n>

Set the operation performed when circuit ER (DTR) signal received from DTE is switched

from ON to OFF while online data mode takes effect.

n=0 : Ignore status (status is always considered to be ON)

n=1 : Move to online command mode when status changes from ON to OFF

n=2 : Disconnect line and move to offline mode when status changes from ON to OFF

(default)

AT&D2

Upper slot : Command

Lower slot : Example

Description

1 2 ... 131 132 133 134 135 136 137 138 139 140 141 ... 147 148

Docomo F-01E Instruction Manual Page 136

Comments to this Manuals

Docomo F-01E Instruction Manual Page 136

Comments to this Manuals

Related products and manuals for Mobile phones Docomo F-01E